Breckwell SW2100 Manuel d'instructions télécharger pdf (Page 17)

Ussc 17

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited, only

burnsmallresinyourstovefortherstfourhoursofoperation.Neveropentheaircontrolmorethannecessaryto

achieve a medium burn rate.

Makesurethatthere’senoughaircirculationwhilecuringthestove.Theodorscouldbesmelledduringthe3or4rst

res.Neverstartyourstoveoutside.Youwillnotbeabletoseeifyouareoverheating.

IGNITION

After making sure that the stove air intake controls are fully open (completely pull-out towards you), place several rumpled

sheets of paper in the centre of the combustion chamber. Place 8 to 10 pieces of small dry kindling wood over the paper

in the form of a tent. You may also place a few pieces of heating wood, but choose the smaller ones. No chemical product

shouldbeusedtolightthere.

Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done in order to

avoid back draft problems often due to negative pressure in the house. If such is the case, open a window slightly near

the stove and twist together a few sheets of newspaper into a torch. Light up this paper torch and hold it as close as

possible to the mouth of the pipe inside the combustion chamber to warm up the chimney. Once the updraft movement

is initiated, you are ready to ignite the stove by lighting the paper and kindling wood inside the combustion chamber.

When you have achieved a good bed of hot embers, we recommend the following burn procedures:

HEATING

Controlledcombustionisthemostefcienttechniqueforwoodheatingbecauseitenablesyoutoselectthetypeof

combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is adjusted

to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will burn quickly if

the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. The air intake control on

your stove is very simple. If you pull on it out completely towards you, it is fully open. If you push on it until it stops the

combustion air is reduced to a minimum. Real operating conditions may give very different results than those obtained

during testing according to the species of wood used, its moisture content, the size and density of the pieces, the length

of the chimney, altitude and outside temperature.

CAUTION: Never alter the damper slide or the adjustment range to increase ring for any reason. Doing so could

result in heater damage and will void your warranty.

SW2100

Primary Air Settings

(Slide Damper is located in center of stove under hearth plate)

(Damper Adjustment: Pulling out on damper increases air)

Electric Blower Speed Setting (Variable)

(BlowerisonHighwhenturned“ON”, Rotate clock-

wiseuntilstopfor“LOW”.)

Burn Rate Adjust Damper from fully closed Burn Time Blower Speed

Low 1/4” (6.3mm) @ 30 minutes Low

Medium - Low 3/8” (9.5mm) @ 30 minutes Low

Medium-High 1/2” (12.7mm) @ 30 minutes Low

High approx. 3” (76mm) all minutes High

SW3100

Burn Rate Adjust Damper from fully closed Burn Time Blower Speed

Low 1/32” (1mm) @ 30 minutes Low

Medium - Low 1/16” (1.5mm) @ 30 minutes Low

Medium-High 5/16” (8mm) @ 30 minutes Low

High approx. 3” (76mm) all minutes High

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

Breckwell SW2100 Manuel d'instructions Page 17

Commentaires sur ces manuels

Produits connexes et manuels pour Poêle à bois Breckwell SW2100